LTC1061 High Performance Triple Universal Filter Building Block U FEATURES DESCRIPTIO The LTC(R)1061 consists of three high performance, universal filter building blocks. Each filter building block together with an external clock and 2 to 5 resistors can produce various second order functions which are available at its three output pins. Two out of three always provide lowpass and bandpass functions while the third output pin can produce highpass or notch or allpass. The center frequency of these functions can be tuned with an external clock or an external clock and a resistor ratio. For Q < 5, the center frequency ranges from 0.1Hz to 35kHz. For Qs of 10 or above, the center frequency ranges from 0.1Hz to 28kHz. Three Filters in a Single Package Up to 6th Order Filter Functions Center Frequency Range up to 35kHz fO x Q Product up to 1MHz Guaranteed Center Frequency and Q Accuracy Over Temperature Guaranteed Low Offset Voltages Over Temperature 90dB Signal-to-Noise Ratio Operation from Single 4.7V Supply, Up to 8V Guaranteed Filter Specifications with 5V Supply and 2.37V Supply Low Power Consumption with Single 5V Supply Clock Inputs T 2L and CMOS Compatible Available in 20-Pin DIP and 20-Pin SO Wide Package The LTC1061 can be used with single or dual supplies ranging from 2.37V to 8V (or 4.74V to 16V). When the filter operates with supplies of 5V and above, it can handle input frequencies up to 100kHz. U APPLICATIO S The LTC1061 is compatible with the LTC1059 single universal filter and the LTC1060 dual. Higher than 6th order functions can be obtained by cascading the LTC1061 with the LTC1059 or LTC1060. Any classical filter realization can be obtained. High Order, Wide Frequency Range Bandpass, Lowpass, Notch Filters Low Power Consumption, Single 5V Supply, Clock-Tunable Filters Tracking Filters Antialiasing Filters , LTC and LT are registered trademarks of Linear Technology Corporation. LTCMOSTM is a trademark of Linear Technology Corporation. All other trademarks are the property of their respective owners. U TYPICAL APPLICATIO Amplitude Response 6th Order, Clock-Tunable, 0.5dB Ripple Chebyshev BP Filter fCLK = 1MHz 2kHz 0 1k 1 20 165k 2 19 78.7k 3 18 4.99k 4 17 5 16 4.99k 165k VIN < 100kHz 7.5V T 2 CLK IN < 1.2MHz V + = 7.5V LTC1061 -20 23.7k 49.9k 6 15 7 14 4.99k 8 13 165k 9 12 5.49k 10 11 V - = -7.5V FILTER GAIN (dB) 9.31k -40 -60 -80 -100 0 VOUT 1061 TA01 10 20 30 40 INPUT FREQUENCY GAIN (kHz) 50 1061 TA02 1061fe 1 LTC1061 W U U W W W AXI U RATI GS U ABSOLUTE PACKAGE/ORDER I FOR ATIO (Note 1) Supply Voltage ....................................................... 18V Power Dissipation ............................................. 500mW Operating Temperature Range LTC1061AC, LTC1061C ............ -40C TA 85C LTC1061AM, LTC1061M ......... -55C TA 125C Storage Temperature Range ................. -65C to 150C Lead Temperature (Soldering, 10 sec.)................ 300C TOP VIEW ORDER PART NUMBER LPA 1 20 LPB BPA 2 19 BPB NA 3 18 NB INVA 4 17 INVB S1A 5 16 S1B AGND 6 15 V - 50/100/HOLD 7 14 LPC CLK 8 13 BPC LSh 9 12 HPC V + 10 11 INVC LTC1061ACN LTC1061CN LTC1061CSW N PACKAGE 20-LEAD PLASTIC DIP SW PACKAGE 20-LEAD PLASTIC SO WIDE LTC1061AMJ LTC1061MJ LTC1061ACJ LTC1061CJ TJMAX = 100C, JA = 100C/W (N) TJMAX = 100C, JA = 85C/W (SW) J PACKAGE 20-LEAD CERAMIC DIP TJMAX = 125C, JA = 100C/W (J) OBSOLETE PACKAGE Consider the N20 Package for Alternate Source Order Options Tape and Reel: Add #TR Lead Free: Add #PBF Lead Free Tape and Reel: Add #TRPBF Lead Free Part Marking: http://www.linear.com/leadfree/ Consult LTC Marketing for parts specified with wider operating temperature ranges. ELECTRICAL CHARACTERISTICS (Complete Filter) The denotes the specifications which apply over the full operating temperature range, otherwise specifications are at VS = 5V, TA = 25C, T2L clock input level, unless otherwise specified. PARAMETER CONDITIONS Center Frequency Range, fO fO x Q 175kHz, Mode 1, VS = 7.5V fO x Q 1.6MHz, Mode 1, VS = 7.5V fO x Q 75kHz, Mode 3, VS = 7.5V fO x Q 1MHz, Mode 3, VS = 7.5V MIN Input Frequency Range Clock-to-Center Frequency Ratio, fCLK /fO LTC1061A LTC1061 LTC1061A LTC1061 Sides A, B: Mode 1, R1 = R3 = 50k R2 = 5k, Q = 10, fCLK = 250kHz Pin 7 High. Side C: Mode 3, R1 = R3 = 50k R2 = R4 = 5k, fCLK = 250kHz Same as Above, Pin 7 at Mid-Supplies, fCLK = 500kHz MAX UNITS Hz Hz Hz Hz 0-200k Hz 50 0.6% 50 1.2% 100 0.6% 100 1.2% Clock-to-Center Frequency Ratio, Side-to-Side Matching LTC1061 Q Accuracy LTC1061A LTC1061 TYP 0.1-35k 0.1-25k 0.1-25k 0.1-17k 1.2% Sides A, B, Mode 1 Side C, Mode 3 fO x Q 50kHz, fO x 5kHz 2 3 5 5 % % 1061fe 2 LTC1061 ELECTRICAL CHARACTERISTICS (Complete Filter) The denotes the specifications which apply over the full operating temperature range, otherwise specifications are at VS = 5V, TA = 25C, T2L clock input level, unless otherwise specified. PARAMETER CONDITIONS fO Temperature Coefficient Q Temperature Coefficient Mode 1, 50:1, fCLK < 300kHz Mode 1, 100:1, fCLK < 500kHz Mode 3, fCLK < 500kHz MIN TYP MAX 1 5 5 UNITS ppm/C ppm/C ppm/C DC Offset Voltage VOS1, Figure 23 VOS2 VOS2 VOS3, LTC1061CN, ACN/LTC1061CS VOS3, LTC1061CN, ACN/LTC1061CS fCLK = 250kHz, 50:1 fCLK = 500kHz, 100:1 fCLK = 250kHz, 50:1 fCLK = 500kHz, 100:1 Clock Feedthrough fCLK < 1MHz 0.4 mVRMS Maximum Clock Frequency Mode 1, Q < 5, VS 5 2.5 MHz Power Supply Current 2 3 6 3 6 6 8 15 30 60 20/25 40/50 11 15 mV mV mV mV mV mA mA (Complete Filter) The denotes the specifications which apply over the full operating temperature range, otherwise specifications are at VS = 2.37V, TA = 25C, unless otherwise specified. Center Frequency Range, fO fO x Q 120kHz, Mode 1, 50:1 fO x Q 120kHz, Mode 3, 50:1 Input Frequency Range Clock-to-Center Frequency Ratio LTC1061A LTC1061 LTC1061A LTC1061 Q Accuracy LTC1061A LTC1061 50:1, fCLK = 250kHz, Q = 10 Sides A, B: Mode 1 Side C, Mode 3, 250kHz 100:1, fCLK = 500kHz, Q = 10 Sides A, B: Mode 1 Side C: Mode 3 0.1- 12k 0.1- 10k Hz Hz 0 - 20k Hz 50 0.6% 50 1.0% 100 0.6% 100 1.0% 2 3 % % Maximum Clock Frequency 700 kHz Power Supply Current 4.5 Same as Above 6 mA (Internal Op Amps) The denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25C, unless otherwise specified. 2.37 Supply Voltage Range Voltage Swings LTC1061A LTC1061 LTC1061, LTC1061A VS = 5V, RL = 5k (Pins 1,2,13,14,19,20) VS = 5V, RL = 3.5k (Pins 3,12,18) 4.0 3.8 3.6 9 V 4.2 4.2 V V V 40/3 mA Output Short-Circuit Current Source/Sink VS = 5V DC Open-Loop Gain VS = 5V, RL = 5k 80 dB GBW Product VS = 5V 3 MHz Slew Rate VS = 5V 7 V/s Note 1: Absolute Maximum Ratings are those values beyond which the life of a device may be impaired. 1061fe 3 LTC1061 U W TYPICAL PERFOR A CE CHARACTERISTICS 0.1 -0.4 fCLK /fO = 50 (TEST POINT) -0.8 -1.2 -1.6 -2.0 -2.4 0 . % DEVIATION (fCLK /fO) -0.1 fCLK /fO = 100 (TEST POINT) -0.2 -0.3 -0.4 -0.5 -0.6 1 10 1 0.1 100 IDEAL Q 10 VS = 5V 20 30 50 20 10 Q<5 DEVIATION FROM IDEAL Q (%) DEVIATION FROM IDEAL Q (%) 10 Q<5 VS = 2.5V 30 20 8 Q=20 10 Q<5 Q=20 10 Q=5 VS = 5V 30 10 20 12 16 20 24 28 32 36 40 CENTER FREQUENCY (kHz) Q=20 1061 G03 Q=5 10 Q=5 Q=1 0 VS = 5V 30 20 Q=20 10 Q=5 4 8 12 16 20 24 CENTER FREQUENCY (kHz) 10 1.5 4 8 12 16 20 24 CENTER FREQUENCY (kHz) 28 VS = 2.5V MODE 1, MODE 3 1.0 0.5 32 1061 G07 20 2.5 Q=1 10 0 TA = 25C fCLK /fO = 50:1 30 20 20 VS = 5V 10 5 2.5 Q=1 32 28 0 4 8 12 16 20 24 28 32 36 40 CENTER FREQUENCY (kHz) 1061 G06 Power Supply Current vs Supply Voltage 30 VS = 7.5V VS = 5V VS = 2.5V MODE 1,3 1.0 VS = 5V MODE 1,3 21 Q = 10 TA = 25C fCLK /fO = 100/1 4 8 TA = 25C 18 15 12 TA = 125C 9 6 VS = 7.5V MODE 1,3 0 TA = -55C 24 MODE 1 MODE 3 1.5 27 MODE 1 MODE 3 0 0 0 Q = 10 TA = 25C fCLK /fO = 50/1 0.5 Q=1 5 Q=1 20 10 0 0 2.0 Q=5 VS = 7.5V 10 5 1061 G05 ERROR FROM IDEAL fCLK /fO (%) Q=20 10 20 VS = 2.5V 20 fCLK/fO vs fO VS = 7.5V 10 20 30 10 2.5 VS = 2.5V 100 Mode 3: (fCLK/fO) = 50:1 VS = 7.5V 0 Mode 3: (fCLK/fO) = 100:1 30 10 IDEAL Q 10 0 4 1 0.1 100 1061 G04 DEVIATION FROM IDEAL Q (%) -0.5 10 10 0 (B) TA = 25C fCLK /fO = 50/1 20 50 TA = 25C fCLK /fO = 50/1 0 -0.3 -0.4 VS = 7.5V 0 0 R2/R4 = 1/2 fCLK /fO = 200:1 -0.2 Mode 1: (fCLK/fO) = 100:1 TA = 25C fCLK /fO = 50/1 VS = 2.5V 10 50 Q<5 20 10 (A) 1061 G02 Mode 1: (fCLK/fO) = 50:1 20 0 -0.1 IDEAL Q 1061 G01 30 fCLK /fO = 500:1 R2/R4 = 1/5 0.1 DEVIATION FROM IDEAL Q (%) 0.1 VS = 5V TA = 25C PIN 7 AT 100:1 ISUPPLY (mA) % DEVIATION (fCLK /fO) 0 VS = 5V TA = 25C fCLK = 500kHz . VS = 5V TA = 25C fCLK = 250kHz 0.4 Mode 3: Deviation of (fCLK/fO) with Respect to Q = 10 Measurement Mode 1, Mode 3 (fCLK/fO) Deviation vs Q DEVIATION OF fCLK /fO WITH RESPECT TO Q = 10 MEASUREMENT (%) Mode 1, Mode 3 (fCLK/fO) Deviation vs Q 3 12 16 20 24 28 32 36 40 CENTER FREQUENCY (kHz) 1061 G08 0 0 1 2 3 4 5 6 7 8 9 POWER SUPPLY VOLTAGE (V) 10 1061 G09 1061fe 4 LTC1061 W BLOCK DIAGRA BPA (2) NA (3) CLK (8) LEVEL SHIFT CLOCK GENERATOR INVA (4) - + TO FILTER A + + LPA (1) + - S1A (5) LEVEL SHIFT CLOCK GENERATOR INVB (17) BPB (19) NB (18) - + TO FILTER B + + LPB (20) + - S1B (16) BPC (13) HPC (12) LEVEL SHIFT CLOCK GENERATOR INVC (11) - + TO FILTER C + LEVEL SHIFT (9) LPC (14) 50/100/ HOLD (7) AGND (6) + V+ (10) V- (15) 1061 BD U U U PI DESCRIPTIO A D APPLICATIO HI TS U U Power Supplies (Pins 10, 15) They should be bypassed with 0.1F disc ceramic. Low noise, nonswitching, power supplies are recommended. The device operates with a single 5V supply, Figure 1, and with dual supplies. The absolute maximum operating power supply voltage is 9V. Clock and Level shift (Pins 8, 9) When the LTC1061 operates with symmetrical dual supplies the level shift Pin 9 should be tied to analog ground. For single 5V supply operation, the level shift pin should be tied to Pin 15 which will be the system ground. The typical logic threshold levels of the clock pin are as follows: 1.65V above the level shift pin for 5V supply operation, 1.75V for 7.5V and above, and 1.4V for single 5V supply operation. The logic threshold levels vary 100mV over the full military temperature range. The recommended duty cycle of the input clock is 50% although for clock frequencies below 500kHz the clock "on" time can be as low as 300ns. The maximum clock frequency for 5V supplies and above is 2.4MHz. S1A, S1B (Pins 5, 16) These are voltage input pins. If used, they should be driven with a source impedance below 5k. when they are not used, they should be tied to the analog ground Pin 6. AGND (Pin 6) When the LTC1061 operates with dual supplies, Pin 6 should be tied to system ground. When the LTC1061 operates with a single positive supply, the analog ground pin should be tied to 1/2 supply, Figure 1. The positive input of all the internal op amps, as well as the common reference of all the internal switches, are internally tied to the analog ground pin. Because of this, a "clean" ground is recommended. 1061fe 5 LTC1061 U U U PI DESCRIPTIO A D APPLICATIO HI TS U U R1 Clock Feedthrough VOUT 1 20 R3 2 19 R3 R2 3 18 R2 4 17 5 2.49k + 1F 2.49k 5V This is defined as the amplitude of the clock frequency appearing at the output pins of the device, Figure 2. Clock feedthrough is measured with all three sides of the LTC1061 connected as filters. The clock feedthrough mainly depends on the magnitude of the power supplies and it is independent from the input clock levels, clock frequency and modes of operation. 16 LTC1061 R1 6 15 7 14 R4 8 13 R3 9 12 R2 10 11 0.1F The Table 2 illustrates the typical clock feedthrough numbers for various power supplies. R1 T2L CLOCK IN fCLK < 1MHz CIN 1061 F01 VIN Figure 1. The 6th Order LP Butterworth Filter of Figure 5 Operating with a Single 5V Supply 50/100/Hold (Pin 7) A = 2V/DIV B = 10mV/DIV By tying Pin 7 to V +, the filter operates with a clock-tocenter frequency internally set at 50:1. When Pin 7 is at mid-supplies, the filter operates with a 100:1 clock-tocenter frequency ratio. Table 1 shows the allowable variation of the potential at Pin 7 when the 100:1 mode is sought. When Pin 7 is shorted to the negative supply pin, the filter operation is stopped and the bandpass and lowpass output act as a sample-and-hold circuit holding the last sample of the input voltage. The hold step is around 2mV and the droop rate is 150V/sec. Table 1 TOTAL POWER SUPPLY (V) VOLTAGE RANGE OF PIN 7 FOR 100:1 OPERATION (V) 5 10 15 2.5 0.5 5 1 7.5 1.5 HORIZONTAL = 10s/DIV 1061 F02 Figure 2. Typical Clock Feedthrogh of the LTC1061 Operating with 5V Supplies. Top Trace is the Input Clock Swinging 0V to 5V and Bottom Trace is One of the Lowpass Outputs with Zero or DC Input Signals. Table 2 POWER SUPPLY (V) CLOCK FEEDTHROUGH (VRMS) 2.5 5 8 0.2 0.4 0.8 Definition of Filter Functions Refer to LTC1060 data sheet. 1061fe 6 LTC1061 W U ODES OF OPERATIO Description and Applications 1. Primary Modes: There are two basic modes of operation, Mode 1 and Mode 3. In Mode 1, the ratio of the external clock frequency to the center frequency of each 2nd order section is internally fixed at 50:1 or 100:1. In Mode 3, this ratio can be adjusted above or below 50:1 or 100:1. The side C of the LTC1061 can be connected only in Mode 3. Figure 3 illustrates Mode 1 providing 2nd order notch, lowpass, and bandpass outputs (for definition of filter functions, refer to the LTC1060 data sheet). Mode 1 can be used to make high order Butterworth lowpass filters; it can also be used to make low Q notches and for cascading 2nd order bandpass functions tuned at the same center frequency and with unity-gain. Mode 3, R3 R2 N VIN R1 - S + LP BP - + 1061 F03 1/3 LTC1061 fCLK ;f =f 100(50) n O R3 R2 HOLP = - R2 ; HOBP = - ; HON1 = - R1 R1 R1 R3 Q= R2 AGND fO = Figure 4, is the classical state variable configuration providing highpass, bandpass and lowpass 2nd order filter functions. Since the input amplifier is within the resonant loop, its phase shift affects the high frequency operation of the filter and therefore, Mode 3 is slower than Mode 1. Mode 3 can be used to make high order all-pole bandpass, lowpass, highpass and notch filters. Mode 3 as well as Mode 1 is a straightforward mode to use and the filter's dynamics can easily be optimized. Figure 5 illustrates a 6th order lowpass Butterworth filter operating with up to 40kHz cutoff frequency and with up to 200kHz input frequency. Sides A, B are connected in Mode 1 while side C is connected in Mode 3. The lower Q section was placed in side C, Mode 3, to eliminate any early Q enhancement. This could happen when the clock approaches 2MHz. The measured frequency response is shown in Figure 6. The attenuation floor is limited by the crosstalk between the three different sections operating with a clock frequency above 1MHz. The measured wideband noise was 150VRMS. For limited temperature range the filter of Figure 5 works up to 2.5MHz clock frequency thus yielding a 50kHz cutoff. VOUT R13 Figure 3. Mode 1: 2nd Order Filter Providing Notch, Bandpass, Lowpass 1 20 R33 2 19 R32 R23 3 18 R22 4 17 CC 5 R4 16 LTC1061 15 7 14 R41 T 2L CLOCK < 2.5MHz 8 13 R31 9 12 R21 V+ 10 11 R3 R2 HP VIN R1 - S + - + LP BP fCLK R2 ; Q = R3 R2 R2 R4 100(50) R4 R3 R4 HOHP = - R2 ; HOBP = - ;H =- R1 OLP R1 R1 fO = NOTE: ADD CC FOR Q > 5 AND fCLK > 1MHz, SUCH AS CC V- R11 1061 F04 VIN 1/3 LTC1061 AGND R12 6 0.16 R4 x 1.2MHz Figure 4. Mode 3: 2nd Order Filter Providing Highpass, Bandpass, Lowpass HARMONIC DISTORTION WITH fCLK = 2MHz fIN 10kHz, 1VRMS 20kHz, 1VRMS 30kHz, 1VRMS 40kHz, 1VRMS 2ND HARMONIC -74dB -62dB -62dB -62dB STANDARD 1% RESISTOR VALUES R11 = 20k R21 = 20k R31 = 11k R41 = 20k R12 = 20k R22 = 20k R32 = 14k R23 = 10k R13 = 10k R33 = 17.8k LTC1061 F05 Figure 5. 6th Order Butterworth Lowpass Filter with Cutoff Frequency up to 45kHz 1061fe 7 LTC1061 W U ODES OF OPERATIO -10 GAIN (dB) the textbook Qs and center frequencies normalized to the ripple bandwidth are: Q1 = 0.55, fO1 = 0.71, Q2 = 1.03, FO2 = 0.969, Q3 = 3.4, FO3 = 1.17. The design was done with speed in mind. The higher (Q3, FO3) section was in Mode 1 and placed in the side B of the LTC1061. The remaining two center frequencies were then normalized with respect to the center frequency of side B; this changes the ratio of clock-to-cutoff frequency from 50:1 to 50 x 1.17 = 58.5:1. As shown in Figure 9, the maximum cutoff frequency is about 33kHz. The total wideband output noise is 220VRMS and the measured output DC offset voltage is 60mV. VS 5V TA = 25C VIN = 1VRMS 0 fCLK = 2MHz fC = 40kHz -20 -30 -40 fCLK = 1MHz fC = 20kHz -50 -60 -70 10k 20k 40k 100k 200k fIN (Hz) 1M 1061 F06 Figure 6. Measures Frequency Response of the Lowpass Butterworth Filter of Figure 3 R51 2. Secondary Modes: Mode 1b - It is derived from Mode 1. In Mode 1b, Figure 7, two additional resistors, R5 and R6, are added to attenuate the amount of voltage fed back from the lowpass output into the input of the SA (SB) switched capacitor summer. This allows the filter clockto-center frequency ratio to be adjusted beyond 50:1 (or 100:1). Mode 1b still maintains the speed advantages of Mode 1. Figure 8 shows the 3 lowpass sections of the LTC1061 in cascade resulting in a Chebyshev lowpass filter. The side A of the IC is connected in Mode 1b to provide the first resonant frequency below the cutoff frequency of the filter. The practical ripple, obtained by using a non-A version of the LTC1061 and 1% standard resistor values, was 0.15dB. For this 6th order lowpass, R6 VIN 19 R32 R21 R22 18 4 17 R61 5 R12 16 R13 6 15 V- 7 14 8 13 R43 9 12 R33 10 11 R23 LTC1061 fCLK < 2MHz V+ VOUT STANDARD 1% RESISTOR VALUES R11 = 35.7k R32 = 36.5k R61 = 2.87k R31 = 11.5k R13 = 15.8k R22 = 11k R51 = 5.49k R33 = 13k R23 = 10.5 R21 = 12.1k R43 = 15.8k R12 = 11k 1061 F08 Figure 8. 6th Order Chebyshev, Lowpass Filter Using 3 Different Modes of Operation for Speed Optimization R5 VS > 5V TA = 25C VIN = 1VRMS fCLK = 1.9MHz 0 - S + - + 1061 F07 fCLK R6 R6 ; f = f ; Q = R3 R2 R5 + R6 100(50) R5 + R6 n O f HON1 (f 0) = HON2 f CLK = - R2 R1 2 R3 HOLP = -R2/R1 ; HOBP = - ; (R5//R6) <5k R1 R6/(R5 + R6) fO = ( ) -10 LP BP VOUT/VIN (dB) N AGND 2 3 R2 R1 20 R11 R3 VIN 1 R31 -20 -30 -40 -50 -60 -70 10k 30k 100k fIN (Hz) 1M 1061 F09 Figure 7. Mode 1b: 2nd Order Filter Providing Notch, Bandpass, Lowpass 8 Figure 9. Amplitude Response of the 6th Order Chebyshev Lowpass Filter of Figure 8 1061fe LTC1061 W U ODES OF OPERATIO Another example of Mode 1b is illustrated on the front page of the data sheet. The cascading sequence of this 6th order bandpass filter is shown in block diagram form, Figure 10a. the filter is geometrically centered around the side B of the LTC1061 connected in Mode 1. This dictates a clock-to-center frequency ratio of 50:1 or 100:1. The side A of the IC operates in Mode 1b to provide the lower center frequency of 0.95 and still share the same clock with the rest of the filter. With this approach the bandpass filter can VIN SIDE A SIDE B SIDE C MODE 1b MODE 1 MODE 3 fO1 = 0.95 Q1 = 31.9 fO2 = 1 Q2 = 15.9 fO3 = 1.05 Q3 = 31.9 VOUT 1061 F10a Figure 10a. Cascading Sequence of the Bandpass Filter Shown on the Front Page, with (fCLK/fO) = 50:1 or 100:1 VIN SIDE A SIDE B SIDE C MODE 1b MODE 1 MODE 3 fO1 = 0.95 Q1 = 31.9 fO2 = 1.05 Q2 = 31.9 fO3 = 1 Q3 = 15.9 VOUT 1061 F10b Figure 10b. Cascading Sequence of the Same Filter for Speed Optimization, and with (fCLK/fO) = 52.6:1 operate with center frequencies up to 24kHz. The speed of the filter could be further improved by using Mode 1 to lock the higher resonant frequency of 1.05 and higher Q or 31.9 to the clock, Figure 10b, thus changing the clock to center frequency ratio to 52.6:1. Mode 3a - This is an extension of Mode 3 where the highpass and lowpass outputs are summed through two external resistors Rh and Rl to create a notch, Figure 11. Mode 3a is very versatile because the notch frequency can be higher or lower than the center frequency of the 2nd order section. The external op amp of Figure 11 is not always required. When cascading the sections of the LTC1061, the highpass and lowpass outputs can be summed directly into the inverting input of the next section. Figure 12 shows an LTC1061 providing a 6th order elliptic bandpass or notch response. Sides C and B are connected in Mode 3a while side A is connected in Mode 1 and uses only two resistors. The resulting filter response is then geometrically symmetrical around either the center frequency of side A (for bandpass responses) or the notch frequency of side A (for notch responses). CC R4 R3 R2 HP VIN R1 - + + S - Rg Rl NOTCH + R3 R4 R2 Rh R2 ; f = fCLK ; HOHP = - ; HOBP = - ; HOLP = - R1 R1 R4 n 100(50) Rl R1 Rg Rg Rg R2 Rg fCLK R4 HON1 (f 0) = x ; HON2 f = x ; HON (f = fO) = Q HOLP - HOHP Rl Rh Rh R1 2 Rl R1 f fO = CLK 100(50) Q = R3 R2 - Rh AGND LP BP ( ) ( EXTERNAL OP AMP OR INPUT OP AMP OF THE LTC1061, SIDES A, B, C ) 1061 F11 R4 R2 NOTE: FOR Q > 5 AND fCLK > 1MHz, ADD CC SUCH AS CC 0.16 R4 x 1.2MHz Figure 11. Mode 3a: 2nd Order Filter Providing Highpass, Bandpass, Lowpass, Notch 1061fe 9 LTC1061 W U ODES OF OPERATIO Rl 2 1 20 R42 R33 2 19 R32 R23 3 18 R22 4 17 5 center frequencies, Qs, and notch frequencies are (fO1 = 0.969, Q1 = 54.3, fn1 = 0.84, fO2 = 1.031, Q2 = 54.3, fn2 = 1.187, fO3 = 1, Q3 = 26.2). The output of the filter is the BP output of Side A, Pin 2. Rh2 16 LTC1061 Rl1 6 15 7 14 R41 T L, CMOS CLOCK INPUT 8 13 R31 9 12 R21 V+ 10 11 2 Lowpass filters with stopband notches can also be realized by using Figure 12 provided that 6th order lowpass filter approximations with 2 stopband notches can be synthesized. Literature describing elliptic double terminated (RLC) V- -10 1061 F12 VOUT/VIN (dB) R11 VIN NOTES: FOR NOTCH RESPONSES, PIN 7 SHOULD BE PREFERABLY CONNECTED TO GROUND AND THE FILTER OUTPUT IS PIN 3. FOR BANDPASS OR LOWPASS RESPONSES, PIN 7 CAN BE EITHER AT GROUND OR POSITIVE SUPPLY, AND THE FILTER OUTPUT IS PIN 2 OR PIN 1. STANDARD 1% RESISTOR VALUES R11 = 165k R21 = 10k R31 = 143k R41 = 13k Rh1 = 10k Rl1 = 10.5k R22 = 20k R32 = 221k R42 = 15.4k Rh2 = 10.5k R23 = 84.5k Rl2 = 10k R33 = 169k BW1 0 R h1 -40 -60 -70 1.0 Figure 13 shows the measured frequency response of the circuit Figure 12 configured to provide a notch function. The filter output is taken out of pin 3. The resistor values are standard 1%. NOTES: USE A 15pF CAPACITOR BETWEEN PINS 17 AND 18. PIN 7 IS GROUNDED. BW2 VS = 5V fCLK = 260kHz 1.5 2.6kHz 2.5 2.0 fIN (kHz) 3.0 3.5 1061 F13 Figure 13. Resistor Values and Amplitude Response of Figure 12 Topology. The Notch is Centered at 2600Hz. 0 STANDARD 1% RESISTOR VALUES R11 = 576k R21 = 10k R31 = 562k R41 = 10.7k Rh11 = 28.7k Rl11 = 40.2k R22 = 10.7k R32 = 562k R42 = 10k Rh2 = 14k R23 = 2.94k Rl2 = 10k R33 = 75k VS = 5V fCLK = 130kHz -10 -20 VOUT/VIN (dB) Figure 14 shows the measured frequency response of the circuit topology, Figure 12, but with pole/zero locations configured to provide a high Q, 6th order elliptic bandpass filter operating with a clock-to-center frequency ratio of 50:1 or 100:1. The theoretical passband ripple, stopband attenuation and stopband to ripple bandwidth ratio are 0.5dB, 56dB, 5:1 respectively. The obtained results with 1% standard resistor values closely match the theoretical frequency response. For this application, the normalized -30 -50 Figure 12. 6th Order Elliptic Bandpass, Lowpass or Notch Topology The ratio of the 0dB width, BW1, to the notch width BW2, is 5:1 and matches the theoretical design value. The measured notch depth was -53dB versus -56dB theoretical and the clock-to-center notch frequency ratio is 100:1. -20 -30 -40 -50 NOTE: FOR CLOCK FREQUENCIES ABOVE 500kHz, CONNECT A 5pF IN PARALLEL WITH R41 AND R42. -60 -70 -80 -90 1.0 1.5 2.5 2.0 fIN (kHz) 3.0 3.5 1061 F14 Figure 14. Resistor Values and Amplitude Response of Figure 12 Topology. The Bandpass Filter is Centered Around 2600Hz when Operating with a 130kHz Clock. 1061fe 10 LTC1061 W U ODES OF OPERATIO -10 -20 VOUT/VIN (dB) Rg STANDARD 1% RESISTOR VALUES R11 = 39.2k R21 = 10k R31 = 13.7k R41 = 39.2k Rh1 = 20.5k Rl1 = 12.4k R22 = 10k R32 = 26.7k R42 = 14k Rh2 = 32.4k R23 = 10k Rl2 = 11.8k R33 = 100k 0 -30 -40 -50 - Rh3 NOTES: USE A 10pF ACROSS R42 FOR fCLK > 1MHz. THE ELLIPTIC LOWPASS FILTER HAS ONLY TWO NOTCHES IN THE STOPBAND, AND IT OPERATES WITH A CLOCK TO CUTOFF FREQUENCY RATIO OF 50:1. -60 -70 -80 -90 0 1 2 3 4 5 6 fIN (kHz) 7 8 9 10 Rl3 + LT1056 R43 1 20 Rl2 R42 R33 2 19 R32 R23 3 18 R22 4 17 1061 F15 5 Figure 15. Resistor Values and Amplitude Response of the Topology of Figure 12 In Figure 16, all three sides of the LTC1061 are connected in Mode 3a. This topology is useful for elliptic highpass and notch filters with clock-to-cutoff (or notch) frequency ratio higher than 100:1. This is often required to extend the allowed input signal frequency range and to avoid premature aliasing. Figure 16 is also a versatile, general purpose architecture providing 3 notches and 4 pole pairs, and there is no restriction on the location of the poles with respect to the notch frequencies. The drawbacks, when compared to Figure 12, are the use of an external op amp and the increased number of the required external resistors. Figure 17 shows the measured frequency of a 6th order highpass elliptic filter operating with 250:1 clock-to-cutoff frequency ratio. With a 1MHz clock, for instance, the filter yields a 4kHz cutoff frequency, thus allowing an input frequency range beyond 100kHz. Band limiting can be easily added by placing a capacitor across the feedback resistor of the external op amp of Figure 16. Rh2 16 LTC1061 6 15 V- Rl1 7 14 R41 T 2Ll, CMOS CLOCK INPUT 8 13 R31 9 12 R21 V+ 10 11 Rh1 R11 VIN 1061 F16 Figure 16. Using an External Op Amp to Connect all 3 Sides of the LTC1061 in Mode 3a STANDARD 1% RESISTOR VALUES R21 = 10k R11 = 105k R41 = 45.3k R31 = 47.5k Rl1 = 1.07M Rh1 = 10k R22 = 32.4k R32 = 28.7k R42 = 52.3k Rh2 = 42.2k R23 = 10k Rl2 = 750k R33 = 255k R43 = 63.4k Rh3 = 10k Rl3 = 110k Rg = 140k fCLK = 250kHz 0 -10 -20 VOUT/VIN (dB) passive ladder filters provide enough data to synthesize the above filters. The measured amplitude response of such a lowpass is shown in Figure 15 where the filter output is taken out of side A's Pin 1, Figure 12. The clockto-center frequency ratio can be either 50:1 or 100:1 because the last stage of the LTC1061 operates in Mode 1 with a center frequency very close to the overall cutoff frequency of the lowpass filter. VOUT -30 -40 -50 -60 NOTE: FOR CLOCK FREQUENCIES BELOW 500kHz, USE A CAPACITOR IN PARALLEL WITH R21 SUCH AS (1/2R21C) fCLK /3. -70 -80 -90 0 0.5 1.5 1.0 fIN (kHz) 2.0 2.5 1061 F17 Figure 17. Measured Amplitude Response of the Topology of Figure 16, Configured to Provide a 6th Order Elliptic Highpass Filter Operating with a Clock-to-Cutoff Frequency Ratio of 250:1 1061fe 11 LTC1061 W U ODES OF OPERATIO When the circuit of Figure 16 is used to realize lowpass elliptic filters, a capacitor across Rg raises the order of the filter and at the same time eliminates any small clock feedthrough. This is shown in Figure 19 where the amplitude response of the filter is plotted for 3 different cutoff frequencies. When the clock frequency equals or exceeds 1MHz, the stopband notches lose their depth due to the finite bandwidth of the internal op amps and to the small crosstalk between the different sides of the LTC1061. The lowpass filter, however, does not lose its passband accuracy and it maintains nearly all of its attenuation slope. The theoretical performance of the 7th order lowpass filter of Figure 19 is 0.2dB passband ripple, 1.5:1 stopband-tocutoff frequency ratio, and 73dB stopband attenuation. Without any tuning, the obtained results closely approximate the textbook response. STANDARD 1% RESISTOR VALUES R11 = 30.9k R21 = 10k R31 = 16.2k R41 = 26.7k Rh1 = 45.3k Rl1 = 19.6k R22 = 10.5k R32 = 100k R42 = 10k Rh2 = 52.3k R23 = 10k Rl2 = 15.8k R33 = 28.7k R43 = 12.7k Rh3 = 95.3k Rl3 = 10k Rg = 28k 0 -10 -20 VOUT/VIN (dB) Figure 18 shows the plotted amplitude responses of a 6th order notch filter operating again with a clock-to-center notch frequency ratio of 250:1. The theoretical notch depth is 70dB and when the notch is centered at 1kHz its width is 50Hz. Two small, noncritical capacitors were used across the R21 and R22 resistors of Figure 16, to bandlimit the first two highpass outputs such that the practical notch depth will approach the theoretical value. With these two fixed capacitors, the notch frequency can be swept within a 3:1 range. fCLK fCLK 200kHz 500kHz -30 fCLK 1MHz -40 -50 -60 -70 -80 -90 1 10 fIN (kHz) 4 100 NOTE: ADD A CAPACITOR C ACROSS Rg TO CREATE A 7TH ORDER LOWPASS SUCH AS (1/2RgC) = (CUTOFF FREQUENCY) x 0.38 1061 F19 Figure 19. Frequency Responses of a 7th Order Lowpass Elliptic Filter Realized with Figure 16 Topology Mode 2 - This is a combination of Mode 1 and Mode 3, Figure 20. With Mode 2, the clock-to-center frequency ratio, fCLK/fO, is always less than 50:1 or 100:1. When compared to Mode 3 and for applications requiring 2nd order section with fCLK/fO slightly less than 100 or 50:1, Mode 2 provides less sensitivity to resistor tolerances. As in Mode 1, Mode 2 has a notch output which directly depends on the clock frequency and therefore the notch frequency is always less than the center frequency, fO, of the 2nd order section. R4 STANDARD 1% RESISTOR VALUES R21 = 10.2k R11 = 84.5k R41 = 63.4k R31 = 31.6k Rl1 = 287k Rh1 = 48.7k R22 = 10k R32 = 232k R42 = 97.6k Rh2 = 10.2k R23 = 20k Rl2 = 66.5k R33 = 300k R43 = 80.6k Rh3 = 10.2k Rl3 = 63.4k Rg = 210k 0 VOUT/VIN (dB) -10 -20 -30 -40 -50 -60 fCLK = 250kHz -70 0 NOTE: CONNECT 39pF AND 100pF ACROSS R21 AND R22 RESPECTIVELY. 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 2.0 fIN (kHz) 1061 F18 Figure 18. 6th Order Band Reject Filter Operating with a Clockto-Center Notch Frequency Ratio of 250:1. The Ratio of 0dB to the - 65dB Notch Width is 8:1. R3 R2 N VIN R1 - + + AGND S - LP BP 1061 F20 fCLK f 1 + R2 ; fn = CLK ; Q = R3 1 + R2 R4 100(50) 100(50) R4 R2 HOLP = -R2/R1 ; HOBP = - R3 R1 1 + (R2/R4) f R2 -R2/R1 HON1 (f 0) = ; HON2 f CLK = - R1 2 1 + (R2/R4) fO = ( ) Figure 20. Mode 2: 2nd Order Filter Providing Notch, Bandpass, Lowpass 1061fe 12 LTC1061 W U ODES OF OPERATIO Figure 21 shows the side A of the LTC1061 connected in Mode 2 while sides B and C are in Mode 3a. This topology can be used to synthesize elliptic bandpass, highpass and notch filters. The elliptic highpass of Figure 17 is synthesized again, Figure 22, but the clock is now locked onto the VOUT Rh2 Rl2 R43 1 20 R42 R33 2 19 R32 R23 3 18 R22 4 17 5 Output Noise 16 LTC1061 T 2L, CMOS CLOCK INPUT V+ Rl1 6 15 7 14 R41 8 13 R31 9 12 R21 10 11 V - Rh1 R11 VIN 1061 F21 Figure 21. LTC1061 with Side A is Connected in Mode 2 While Side B, C are in Mode 3a. Topology is Useful for Elliptic Highpass, Notch and Bandpass Filters. STANDARD 1% RESISTOR VALUES R11 = 54.9k R21 = 24.3k R31 = 34.8k R41 = 10k Rh1 = 28.7k Rl1 = 280k R22 = 68.1k R32 = 18.2k R42 = 10k Rh2 = 10.2k R23 = 10k Rl2 = 16.2k R33 = 75k R43 = 14k 0 -10 VOUT/VIN (dB) -20 -30 -40 -50 NOTE: FOR CLOCK FREQUENCIES ABOVE 300kHz, ADD A CAPACITOR C ACROSS R21 AND R22 SUCH AS (1/2R21C) = fCLK -60 -70 -80 -90 0 1 2 3 4 5 6 fIN (kHz) 7 8 9 higher frequency notch provided by the side A of the LTC1061. As shown in Figure 22, the highpass corner frequency is 3.93kHz and the higher notch frequency is 3kHz while the filter operates with a 300kHz clock. The center frequencies, Qs, and notches of Figure 22, when normalized to the highpass cutoff frequency, are (fO1 = 1.17, Q1 = 2.24, fn1 = 0.242, fO2 = 1.96, Q2 = 0.7, fn2 = 0.6, fO3 = 0.987, fn3 = 0.753, Q3 = 10). When compared with the topology of Figure 16, this approach uses lower and more restricted clock frequencies. The obtained notch in Mode 2 is shallower although the topology is more efficient. 10 1061 F22 The wideband RMS noise of the LTC1061 outputs is nearly independent from the clock frequency. The LTC1061 noise when operating with 2.5V supply is lower, as Table 3 indicates. The noise at the bandpass and lowpass outputs increases rough as the Q. Also the noise increases when the clock-to-center frequency ratio is altered with external resistors to exceed the internally set 100:1 or 50:1 ratios. Under this condition, the noise increases square root-wise. Output Offsets The equivalent input offsets of the LTC1061 are shown in Figure 23. The DC offset at the filter bandpass output is always equal to VOS3. The DC offsets at the remaining two outputs (Notch and LP) depend on the mode of operation and external resistor ratios. Table 4 illustrates this. It is important to know the value of the DC output offsets, especially when the filter handles input signals with large dynamic range. As a rule of thumb, the output DC offsets increase when: 1. The Qs decrease 2. The ratio (fCLK/fO) increases beyond 100:1. This is done by decreasing either the (R2/R4) or the R6/(R5 + R6) resistor ratios. Figure 22. 6th Order Elliptic Highpass Filter Operating with a Clock-to-Cutoff Frequency Ratio of 75:1 and Using the Topology of Figure 21 1061fe 13 LTC1061 W U ODES OF OPERATIO Table 3. Wideband RMS Noise VS (V) fCLK/fO NOTCH/HP (VRMS) BP (VRMS) LP (VRMS) 5.0 5.0 2.5 2.5 50:1 100:1 50:1 100:1 45 65 30 40 55 65 30 40 70 85 45 60 5.0 5.0 2.5 2.5 50:1 100:1 50:1 100:1 18 20 15 17 150 200 100 140 150 200 100 140 5.0 5.0 2.5 2.5 50:1 100:1 50:1 100:1 57 72 40 50 57 72 40 50 62 80 42 53 Mode 3, R1 = R2 = R3 = R4 Q=1 5.0 5.0 2.5 2.5 50:1 100:1 50:1 100:1 135 170 100 125 120 160 88 115 140 185 100 130 Mode 3, R2 = R4, Q = 10 R3 = R1 for BP Out R4 = R1 for LP and HP Out (11,17) 4 +V OS1 - - 3 + VOS2 - + Mode 1, R1 = R2 = R3 Q=1 Mode 1, Q = 10 R1 = R3 for BP Out R1 = R2 for LP Out 2 (13,19) (12,18) + CONDITIONS - - + VOS3 1 (14,20) - - + 5 + 6 1061 F23 Figure 23. Equivalent Input Offsets of 1/3 LTC1061 Filter Building Block Table 4 VOSN PIN 3 (18) MODE VOSBP PIN 2 (19) VOSLP PIN 1 (20) 1 VOS1 [(1/Q) + 1 + || HOLP ||] - VOS3/Q VOS3 VOSN - VOS2 1b VOS1 [(1/Q) + 1 + R2/R1] - VOS3/Q VOS3 ~(VOSN - VOS2)(1 + R5/R6) 2 [VOS1 (1 + R2/R1 + R2/R3 + R2/R4) - VOS3(R2/R3)] x x [R4/(R2 + R4)] + VOS2[R2/(R2 + R4)] VOS3 VOSN - VOS2 3 VOS2 VOS3 VOS1 (1 + R4/R1 + R4/R2 + R4/R3) - VOS2(R4/R2) - VOS3 (R4/R3) 1061fe 14 LTC1061 U PACKAGE DESCRIPTIO J Package 20-Lead CERDIP (Narrow .300 Inch, Hermetic) (Reference LTC DWG # 05-08-1110) 1.060 (26.924) MAX CORNER LEADS OPTION (4 PLCS) .023 - .045 (0.584 - 1.143) HALF LEAD OPTION 20 19 18 17 16 15 14 13 12 11 1 2 3 4 5 6 7 8 9 10 .025 .220 - .310 (5.588 - 7.874) (0.635) RAD TYP .045 - .065 (1.143 - 1.650) FULL LEAD OPTION .005 (0.127) MIN .300 BSC (7.62 BSC) .200 (5.080) MAX .015 - .060 (0.381 - 1.524) .008 - .018 (0.203 - 0.457) 0 - 15 NOTE: LEAD DIMENSIONS APPLY TO SOLDER DIP/PLATE OR TIN PLATE LEADS .125 (3.175) MIN .045 - .065 (1.143 - 1.651) .100 (2.54) BSC .014 - .026 (0.356 - 0.660) J20 0801 OBSOLETE PACKAGE N Package 20-Lead PDIP (Narrow .300 Inch) (Reference LTC DWG # 05-08-1510) 1.060* (26.924) MAX 20 19 18 17 16 15 14 13 12 11 1 2 3 4 5 6 7 8 9 10 .255 .015* (6.477 0.381) .300 - .325 (7.620 - 8.255) .008 - .015 (0.203 - 0.381) ( +.035 .325 -.015 +0.889 8.255 -0.381 ) .045 - .065 (1.143 - 1.651) .125 - .145 (3.175 - 3.683) .020 (0.508) MIN .065 (1.651) TYP .120 (3.048) MIN .005 (0.127) MIN .100 (2.54) BSC .018 .003 (0.457 0.076) NOTE: 1. DIMENSIONS ARE INCHES MILLIMETERS *THESE DIMENSIONS DO NOT INCLUDE MOLD FLASH OR PROTRUSIONS. MOLD FLASH OR PROTRUSIONS SHALL NOT EXCEED .010 INCH (0.254mm) N20 0405 1061fe Information furnished by Linear Technology Corporation is believed to be accurate and reliable. However, no responsibility is assumed for its use. Linear Technology Corporation makes no representation that the interconnection of its circuits as described herein will not infringe on existing patent rights. 15 LTC1061 U PACKAGE DESCRIPTIO SW Package 20-Lead Plastic Small Outline (Wide .300 Inch) (Reference LTC DWG # 05-08-1620) .050 BSC .045 .005 .030 .005 TYP .496 - .512 (12.598 - 13.005) NOTE 4 N 20 18 17 16 15 14 13 12 11 N .325 .005 .420 MIN 19 .394 - .419 (10.007 - 10.643) NOTE 3 1 2 3 N/2 N/2 RECOMMENDED SOLDER PAD LAYOUT .291 - .299 (7.391 - 7.595) NOTE 4 .010 - .029 x 45 (0.254 - 0.737) .005 (0.127) RAD MIN 1 2 3 4 5 6 7 8 9 10 .037 - .045 (0.940 - 1.143) .093 - .104 (2.362 - 2.642) 0 - 8 TYP .009 - .013 (0.229 - 0.330) .050 (1.270) BSC NOTE 3 NOTE: 1. DIMENSIONS IN .004 - .012 (0.102 - 0.305) .014 - .019 (0.356 - 0.482) TYP .016 - .050 (0.406 - 1.270) S20 (WIDE) 0502 INCHES (MILLIMETERS) 2. DRAWING NOT TO SCALE 3. PIN 1 IDENT, NOTCH ON TOP AND CAVITIES ON THE BOTTOM OF PACKAGES ARE THE MANUFACTURING OPTIONS. THE PART MAY BE SUPPLIED WITH OR WITHOUT ANY OF THE OPTIONS 4. THESE DIMENSIONS DO NOT INCLUDE MOLD FLASH OR PROTRUSIONS. MOLD FLASH OR PROTRUSIONS SHALL NOT EXCEED .006" (0.15mm) RELATED PARTS PART NUMBER DESCRIPTION COMMENTS LTC1068 Quad, Universal, Filter Building Block 25:1, 50:1, 100:1, 200:1 FC:FCLK Ratios Available LTC1562 Quad, Universal, Filter Building Block Continuous Time, Active RC, FC < 150kHz LTC1562-2 Quad, Universal, Filter Building Block Continuous Time, Active RC, FC < 360kHz 1061fe 16 Linear Technology Corporation LT/LT 0905 REV E * PRINTED IN USA 1630 McCarthy Blvd., Milpitas, CA 95035-7417 (408) 432-1900 FAX: (408) 434-0507 www.linear.com (c) LINEAR TECHNOLOGY CORPORATION 1994